Readout on display: — Press Q Q. G 1552- and the control unit. Installing — Swivel door handle into the door. Observe the safety instructions during use. G 1552-, are listed in the table according to the 5-digit fault code.
Channel number Area to be adapted 01 Passenger-side front airbag 03 Passenger side side airbag After the front passenger side airbag units have been disabled, the warning light -K75- comes on at first for about 4 seconds after the ignition is switched on, and then flashes for about 12 seconds. This completes the basic setting and simultaneously activates the automatic depth run function. Readout on display: — Enter function 07. When cleaning the vehicle interior do not press against the freshly glued window. Installing — Insert window in frame. Installing Installation is carried out in the reverse order. The starter or engine can be damaged if the starter is Starting-off and Driving activated when the engine is running ».
The problem is that once you have gotten your nifty new product, the Fabia Ii Manual Pdf gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Note Mount the interior rear-view mirror after 15 minutes. In the event of paint damage in a non-visible area apply the following repair method: — Cover twice wet on wet with paint primer - D 009 200 02-. T Installing: The installation occurs in reverse order. Draw the heating cable through the cover.
On vehicles with a manual transmission, only push down on the accelerator pedal once the rope is taught. All keys must be initialised during a single initialisation process. Before screwing on the wing insert a galvanized washer under the screws at the impact points in the wheelhouse zone and pillar A, e. The driver can only operate the key switch with the ignition key when the ignition is switched off. The switching on and off operations are undertaken by means of the key switch for the front passenger airbag if the vehicle is fitted with such a key switch.
Grip this section only; otherwise, there is an accident risk! Note If the screw is unscrewed too far the catch may separate from the bracket and fall inside the door. Installing Installation is carried out in the reverse order. Installing Installation is carried out in the reverse order. Overview of the airbag system control units Vehicle equipment Parts No. Nobody should be in the vehicle when the battery is being connected. Installing Installation is carried out in the reverse order. The vehicle is only safe for driving after the waiting time has expired.
Nobody should be in the vehicle when the battery is being connected. Caution: Comply with the manufacturer's handling instructions. Pull out can holder -3- from centre section of dashboard. Display group number 012 Display field Readout on display Denomination 1 to 4 No display1 1 Rectifying fault Ignore. If the display content does not change during activation, rectify fault or replace the relevant component. Glue remover Removes glue residues 1 2 3 -D002 000 10- Order volume 25 pieces Must not be used on glued surfaces before glueing. Installing: Installation is carried out in the reverse order.
This cable consists of an independent electrical circuit, which has no connection to other electrical systems in the vehicle. The door will drop again at the following overpressures. Note If the airbag warning light -K75- signals a fault after assembly, erase the fault memory with fault reader - V. Opening the air inlet when the air conditioning system is on causes fresh or in- Fig. Offer up the cap to the rear bumper » Fig. Installing Installation is carried out in the reverse order.
Repairs to body parts are usually cheaper. If the display content does not change: — Replace defective wiring or plug connections. T Installing: Installation is carried out in the reverse order. Unhook the transverse wire of the backrest rack -4- at the rear of the backrest side. Cuts, tears or chafing spots. S 5232- onto plug connector of the airbag.
All pages are printable, so print off what you need and take it with you anywhere. Note Do not damage the painted surfaces. Removing and installing the convenience system central control unit Removing Note The convenience system central control unit is located below the dash panel in area above accelerator pedal in the bracket at the dash panel support. Each desired airbag unit or safety belt can be blocked for the airbag system control unit. End measured value block test: — Press C key.
This is done by touching an earthed metal part, such as e. Control dial settings » Fig. Also advise your passengers to adopt driving so that the position of the steering wheel cannot accidently change the correct seated position and not to change this position while the car is during the journey —. Check correct fitting and tightness of the wiring and plug connections with the ignition off also possibly disconnect the plug connections. Seat belts which are not correctly adjusted can themselves cause injuries even in mi- nor accidents. Readout on display: — Confirm the entry with key Q. Pay special attention to examining the seat belts.